Élastomère polyuréthane brossable

Achetez Smooth-On chez FormX

Smooth-On est l'un des principaux fabricants mondiaux de matériaux de modélisation 3D tels que les matériaux de fabrication de moules, de coulée et d'effets spéciaux, mais aussi les résines de coulée industrielles, les adhésifs et les équipements. FormX est le principal distributeur des produits Smooth-On en Europe.

Brush-On 35

Les Brush-On sont des élastomères polyuréthanes pour des applications au pinceau (ou spatule) en plusieurs couches successives.
Très polyvalents, les Brush-On sont connus pour leur très grande résistance à l'abrasion, à la déchirure et pour leur retrait négligeable.
Apprécié pour sa facilité d'utilisation (mélange 1:1), la série Brush-On répondra parfaitement aux demandes de prises d'empreintes verticales, tout en capturant les moindres détails de vos modèles d'origine.
Idéal pour les reproductions d'objets (sculptures, bas-reliefs,...) la restauration architecturale (murs, plafonds, corniches,...), la fabrication de moules-chaussettes, l´élastomères BRUSH-ON 35 est parfaitement adapté aux tirages de béton et autres matériaux abrasifs. Facile à mélanger et à appliquer avec un pinceau ou une spatule, BRUSH-ON 35 s'applique sur les surfaces verticales et durcit avec un retrait négligeable pour donner un caoutchouc durable qui fonctionne en production. Parmi les applications courantes de BRUSH-ON 35 figurent les moules de restauration architecturale sur site, la reproduction de sculptures (moules à la cire d’art bronze - procédé à la cire perdue) et la fabrication d’effets spéciaux.

Il est possible de réduire le shore (dureté) avec l'ajout de So-Flex.

Dureté Shore: 35 A
Résistance à la traction: 10 N / mm
Durée de vie en pot: 20 min
Temps avant durcissement: 16 heures

Fiche technique séries Brush-On

Safety Brush-On part B

- Lisez les informations de sécurité cliquez sur l'image

- Lea la etiqueta de información de seguridad. Haga clic en la imagen

- Lees het veiligheidsinformatie label. Klik op de afbeelding.

- Lesen Sie das Sicherheitsinformationsetikett. Klicken Sie auf das Bild.

- Read the safety information label. Click on the image

Produits Brush-On

Faire un moule composé souple/dur

Brush-On 35 peut très bien être utilisé en combinaison avec Plasti-Paste pour créer un moule composé avec un intérieur souple et un extérieur dur. Un tel moule est réalisé en appliquant la Plasti-Paste sur le moule Brush-On sans l'aide d'un agent de démoulage. Les deux matériaux d'uréthane vont maintenant être liés ensemble pour faire une couche de composé solide. Un tel moule est très approprié pour les grandes pièces moulées, par exemple béton.

Brush-On 35 peut très bien être utilisé en association avec Plasti-Paste pour créer un moule composite avec un intérieur flexible et un extérieur dur. Un tel moule est réalisé en appliquant la plasti-pâte sur le moule Brush-On sans utiliser d'agent de démoulage. Les deux matériaux d'uréthane vont maintenant se lier pour former une couche composite solide. De tels moules sont très bien adaptés aux gros moulages, par exemple. béton.

Faire un moule composé, BO-35 et Plasti-Paste

Vous pourriez aussi avoir besoin de...

Preparation - Materials should be stored and used in at room 23°C. Humidity should be low. These products have a limited shelf life and should be used as soon as possible. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Good ventilation (room size) is necessary.

Some Materials Must Be Sealed - To prevent adhesion between the rubber and model surface, models made of porous materials (gypsum plasters, concrete, wood, stone, etc.) must be sealed prior to applying a release agent. SuperSeal™ or One Step™ available from form X are fast drying sealers suitable for sealing porous surfaces without interfering with surface detail. Shellac is suitable for rough contours. A high quality spray shellac is suitable for sealing modeling clays that contain sulfur or moisture (water based). Thermoplastics (polystyrene) must also be sealed with shellac or PVA.

In all cases, the sealing agent should be applied and allowed to completely dry prior to applying a release agent.

Non-Porous Surfaces - Metal, glass, hard plastics, sulfur free clays, etc. require only a release agent.

Applying A Release Agent - A release agent is necessary to facilitate demolding when casting into or over most surfaces. Use a release agent made specifically for mold making (Universal™ Mold Release available from form x). A liberal coat of release agent should be applied onto all surfaces that will contact the rubber.

IMPORTANT: To ensure thorough coverage, lightly brush the release agent with a soft brush over all surfaces of the model. Follow with a light mist coating and let dry for 30 minutes. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

IMPORTANT: Shelf life of product is reduced after opening. Remaining product should be used as soon as possible. Immediately replacing the lids on both containers after dispensing product will help prolong the shelf life of the unused product. XTEND-IT™ Dry Gas Blanket (available from Smooth-On) will significantly prolong the shelf life of unused liquid urethane products.

MEASURING & MIXING - Liquid urethanes are moisture sensitive and will absorb atmospheric moisture. Mixing tools and containers should be clean and made of metal, glass or plastic. Materials should be stored and used in a warm environment 23°C.

Mixing - Part A is a paste with the consistency of cake frosting. Fill a container to the top with this paste, making sure to eliminate any large voids. Level off the top of the container and remove any excess material. The paste should then be thoroughly emptied into a larger container that will act as your mixing container. Next, fill the original container to the top with Part B (liquid) and empty it into the mixing container. After dispensing equal amounts of Parts A and B into mixing container, mix thoroughly for 3 minutes making sure that you scrape the sides and bottom of the mixing container several times.

Applying The Rubber - This product must be applied in layers. Mold makers generally find that four to six layers (minimum 3/8”) thickness is suitable for a working mold. Using a stiff brush, the first coat of rubber should be applied in a thin layer to capture intricate detail. Use dabbing strokes, especially around undercuts, to reduce entrapped air. Subsequent coats will add strength to the mold. Let the first coat dry for 30-40 minutes at room temperature or when it becomes “tacky” before adding the next coat. Repeat until the necessary thickness is achieved. Do not allow rubber to fully cure between layers, as delamination may result. Note: Although not necessary, adding a small amount of SO-Strong™ liquid color pigment available at form X to every other mix of rubber will help you distinguish one layer from the next. This will ensure that you apply a thorough coating each time and help build uniform layers.

Curing - Allow rubber to cure overnight (at least 16 hours) at room temperature 23°C before demolding. Cure time can be reduced with mild heat or by adding Smooth-On “Kick-It™” Cure Accelerator. Do not cure rubber where temperature is less than 18°C.

Post Curing - After rubber has cured at room temperature, heating the rubber to 65°C for 4 to 8 hours will increase physical properties and performance.

Apply A Support Shell - Once the mold is fully cured, a rigid support shell (mother mold) is needed to support the rubber mold during casting. Plasti-Paste™ II is a trowelable plastic which is ideal as a mother mold material.

Using The Mold - If using as a mold material, a release agent should be applied to the mold before each casting. The type of release agent to use depends on the material being cast. The proper release agent for wax, liquid rubber or thermosetting materials (i.e. Smooth-On liquid plastics) is a spray release made specifically for mold making (available from Smooth-On or your distributor). Prior to casting gypsum plaster materials, sponge the mold with a soap solution for better plaster flow and easy release. In & Out™ II Water Based Release Concentrate available from form x is recommended for releasing abrasive materials like concrete.

Performance & Storage - Fully cured molds are tough, durable and will perform if properly used and stored. The physical life of the mold depends on how you use it (materials cast, frequency, etc.). Before storing, the mold should be cleaned with a soap solution and wiped fully dry. Two part (or more) molds should be assembled. Molds should be stored on a level surface in a cool, dry environment. Do not stack molds, expose them to moisture or UV light.

Seaux, gobelets gradués et balances de pesée

pinceaux plats jetables

Masques, filtres et gants latex et vinyle.

Agents de démoulage

(C) 2010 / 2011 - Tous droits réservés

Imprimer cette page